All of our products are designed and built in USA.
Our gear simply remove the wires between controller, valves, pumps, and sensors in your irrigation setup.
Use a regular 24V valve as is, no need to change the solenoid to a DC solenoid.
WB-312T/331T/363T/3127MT/3255MT are single transmitters that can handle up to 12, 31, 63, 127, and 255 Zones each. Each valve would need its own receiver to be activated by the transmitter. They can also be used to combine multiple controllers in one single location for ease of operation (with WB-312R, WB-331R or WB-363R).
WB-124 and WB-100 are designed to connect single 24V-AC valve to controller. It is a single transmitter and receiver kit combination. Receiver is powered by an internal battery that is charged with a solar panel (included in the box), there is no need to change batteries.
WR-115/230 is a wireless Pump Start Relay with 24V-AC output and can create a wireless connection between a controller and a pump. They simply replace the wires between the controller and pump's contactor. Multiple controllers can control single pump using these products without the need for any additional safety devices.
WR-110 is a wireless Pump Starter Relay. It creates a wireless connection between a controller and a pump that does not have any contactor. This kit has a built-in contactor that is rated at 30A.
If there is a contactor already in the system, then WR-110 is NOT the right choice for the project.
WB-712 can accept up to 12 moisture sensors (WS-601/621) for a wired system to allow both controller and a moisture sensor operate the valve independently.
WS-601/621 is a moisture sensor kit that can turn a valve ON/OFF (via WB-100R or WB-200R) and set the irrigation to run based on the soil moisture. WS-601 can operate in parallel with a controller, so a controller or WS-601 can turn the valve On/Off. WS-621 is designed to operate during night time, WS-601 runs 24/7.
WS-602 is an inline switch for any 24V valve. It senses soil moisture and opens the valve only when controller activates the valve. This products is designed for a wired setup.
WB-801 kit provides a wireless connection between a standard pulse based flow sensor and a controller. Effectively it can convert a traditional wired flow sensor to a wireless device and eliminate the need to run wires back to controller.
WB-312R/331R/363R is 12, 31 and 63 zone wireless receiver that can connect various number of zones to a controller and effectively combine two (or more) controllers into one larger controller in a one location.
WR-400X is a customized wireless pump start relay for any specified voltage. Let us know how we can meet your needs for your pump.
We can also create custom solution per request. Just let us know how we can help and we will get it done.
Our gear simply remove the wires between controller, valves, pumps, and sensors in your irrigation setup.
Use a regular 24V valve as is, no need to change the solenoid to a DC solenoid.
WB-312T/331T/363T/3127MT/3255MT are single transmitters that can handle up to 12, 31, 63, 127, and 255 Zones each. Each valve would need its own receiver to be activated by the transmitter. They can also be used to combine multiple controllers in one single location for ease of operation (with WB-312R, WB-331R or WB-363R).
WB-124 and WB-100 are designed to connect single 24V-AC valve to controller. It is a single transmitter and receiver kit combination. Receiver is powered by an internal battery that is charged with a solar panel (included in the box), there is no need to change batteries.
WR-115/230 is a wireless Pump Start Relay with 24V-AC output and can create a wireless connection between a controller and a pump. They simply replace the wires between the controller and pump's contactor. Multiple controllers can control single pump using these products without the need for any additional safety devices.
WR-110 is a wireless Pump Starter Relay. It creates a wireless connection between a controller and a pump that does not have any contactor. This kit has a built-in contactor that is rated at 30A.
If there is a contactor already in the system, then WR-110 is NOT the right choice for the project.
WB-712 can accept up to 12 moisture sensors (WS-601/621) for a wired system to allow both controller and a moisture sensor operate the valve independently.
WS-601/621 is a moisture sensor kit that can turn a valve ON/OFF (via WB-100R or WB-200R) and set the irrigation to run based on the soil moisture. WS-601 can operate in parallel with a controller, so a controller or WS-601 can turn the valve On/Off. WS-621 is designed to operate during night time, WS-601 runs 24/7.
WS-602 is an inline switch for any 24V valve. It senses soil moisture and opens the valve only when controller activates the valve. This products is designed for a wired setup.
WB-801 kit provides a wireless connection between a standard pulse based flow sensor and a controller. Effectively it can convert a traditional wired flow sensor to a wireless device and eliminate the need to run wires back to controller.
WB-312R/331R/363R is 12, 31 and 63 zone wireless receiver that can connect various number of zones to a controller and effectively combine two (or more) controllers into one larger controller in a one location.
WR-400X is a customized wireless pump start relay for any specified voltage. Let us know how we can meet your needs for your pump.
We can also create custom solution per request. Just let us know how we can help and we will get it done.